diff -r 3d43b280298c util/av7110_loadkeys/README
--- a/util/av7110_loadkeys/README	Fri Mar 21 20:26:36 2014 +0100
+++ b/util/av7110_loadkeys/README	Wed Jan 06 13:46:28 2016 +0200
@@ -5,7 +5,7 @@
 
 just call
 
-   # ./av7110_loadkeys [-i|--invert] [-a|--address <num>] keymapname.(rc5|rcmm) > /proc/av7110_ir
+   # av7110_loadkeys [-i|--invert] [-a|--address <num>] keymapname.(rc5|rcmm) > /proc/av7110_ir
 
 If your IR receiver hardware inverts the signal, you should use the -i
 or --invert command line option.
@@ -15,17 +15,17 @@
 driver listens to all device addresses. Some examples:
 
 Listen to *any* IR transmitter with uses the RC5 protocol:
-# ./av7110_loadkeys hauppauge.rc5 > /proc/av7110_ir
+# av7110_loadkeys hauppauge.rc5 > /proc/av7110_ir
 
 Listen to RC5 transmitter with address 2:
-# ./av7110_loadkeys -a 2 hauppauge.rc5 > /proc/av7110_ir
+# av7110_loadkeys -a 2 hauppauge.rc5 > /proc/av7110_ir
 
 If you don't know the correct value for the -a parameter, take a look
 on the debug output of the driver (see below).
 
 Now you can test your hardware setup using evtest
 
-   # ./evtest /dev/input/eventX
+   # evtest /dev/input/eventX
 
 where eventX is the IR input event device, usually event0 if you don't
 use USB mice or keyboards.
diff -r 3d43b280298c util/scan/README
--- a/util/scan/README	Fri Mar 21 20:26:36 2014 +0100
+++ b/util/scan/README	Wed Jan 06 13:46:28 2016 +0200
@@ -8,13 +8,13 @@
 If you make a new one or improve uppon existing ones feel free to submit it to
 the linux-dvb mailing list http://www.linuxtv.org/lists.php.
 
-Basic usage: ./dvbscan dvb-s/Astra-19.2E | tee mychannels.conf
-or           ./atscscan atsc/us-NTSC-center-frequencies-8VSB
+Basic usage: dvbscan dvb-s/Astra-19.2E | tee mychannels.conf
+or           atscscan atsc/us-NTSC-center-frequencies-8VSB
 
 If you want it to check a specific frequency, tune to that frequency
-(e.g. using szap/tzap/czap/azap) and then use './dvbscan -c' or './atscscan -c'.
+(e.g. using szap/tzap/czap/azap) and then use 'dvbscan -c' or 'atscscan -c'.
 
-For more scan options see ./dvbscan -h or ./atscscan -h
+For more scan options see dvbscan -h or atscscan -h
 
 atscscan is _just_ a copy of dvbscan to not confuse ATSC-user.
 
diff -r 3d43b280298c util/szap/README
--- a/util/szap/README	Fri Mar 21 20:26:36 2014 +0100
+++ b/util/szap/README	Wed Jan 06 13:46:28 2016 +0200
@@ -5,19 +5,19 @@
 
 For DVB-S, Astra Channel config file:
 
-$ ./szap -c channels-conf/dvb-s/Astra-19.2E n24
+$ szap -c channels-conf/dvb-s/Astra-19.2E n24
 
 will tune to N24. For DVB-C, Berlin Cable channel config:
 
-$ ./czap -c channels-conf/dvb-c/de-Berlin Arte
+$ czap -c channels-conf/dvb-c/de-Berlin Arte
 
 For DVB-T, Berlin Config:
 
-$ ./tzap -c channels-conf/dvb-t/de-Berlin phoenix
+$ tzap -c channels-conf/dvb-t/de-Berlin phoenix
 
 For ATSC, Raleigh Durham Config:
 
-$ ./azap -c channels-conf/atsc/us-Raleigh-Durham WRAL
+$ azap -c channels-conf/atsc/us-Raleigh-Durham WRAL
 
 will tune to WRAL's Digital Channel 5-1.
 
@@ -25,7 +25,7 @@
 record the stream to disk you will route it to the DVR device by using the
 '-r' option:
 
-$ ./tzap -c channels-conf/dvb-t/de-Berlin phoenix -r
+$ tzap -c channels-conf/dvb-t/de-Berlin phoenix -r
 [keep it running in one console]
 $ cat /dev/dvb/adapter0/dvr0 > /tmp/recording.ts
 [in a second console, will dump the MPEG transport stream to /tmp/recording.ts]