From bce4fe9fa48df0cbbe842e80d9a520f7265b4cd4 Mon Sep 17 00:00:00 2001
From: Dave Stevenson <dave.stevenson@raspberrypi.org>
Date: Wed, 4 Apr 2018 16:34:24 +0100
Subject: [PATCH 5/9] net: lan78xx: Allow for VLAN headers in timeout.
The frame abort timeout being set by lan78xx_set_rx_max_frame_length
didn't account for any VLAN headers, resulting in very low
throughput if used with tagged VLANs.
Use VLAN_ETH_HLEN instead of ETH_HLEN to correct for this.
See https://github.com/raspberrypi/linux/issues/2458
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
---
drivers/net/usb/lan78xx.c | 5 +++--
1 file changed, 3 insertions(+), 2 deletions(-)
diff --git a/drivers/net/usb/lan78xx.c b/drivers/net/usb/lan78xx.c
index 0867f7275852..5b46998a6dce 100644
--- a/drivers/net/usb/lan78xx.c
+++ b/drivers/net/usb/lan78xx.c
@@ -2178,7 +2178,7 @@ static int lan78xx_change_mtu(struct net_device *netdev, int new_mtu)
if ((ll_mtu % dev->maxpacket) == 0)
return -EDOM;
- ret = lan78xx_set_rx_max_frame_length(dev, new_mtu + ETH_HLEN);
+ ret = lan78xx_set_rx_max_frame_length(dev, new_mtu + VLAN_ETH_HLEN);
netdev->mtu = new_mtu;
@@ -2467,7 +2467,8 @@ static int lan78xx_reset(struct lan78xx_net *dev)
buf |= FCT_TX_CTL_EN_;
ret = lan78xx_write_reg(dev, FCT_TX_CTL, buf);
- ret = lan78xx_set_rx_max_frame_length(dev, dev->net->mtu + ETH_HLEN);
+ ret = lan78xx_set_rx_max_frame_length(dev,
+ dev->net->mtu + VLAN_ETH_HLEN);
ret = lan78xx_read_reg(dev, MAC_RX, &buf);
buf |= MAC_RX_RXEN_;
--
2.17.0
From 6fecd97fd35e9c624d101495ca34c83b1cb23e3d Mon Sep 17 00:00:00 2001
From: Dave Stevenson <dave.stevenson@raspberrypi.org>
Date: Mon, 9 Apr 2018 14:31:54 +0100
Subject: [PATCH 6/9] net: lan78xx: Request s/w csum check on VLAN tagged
packets.
There appears to be some issue in the LAN78xx where the checksum
computed on a VLAN tagged packet is incorrect, or at least not
in the form that the kernel is after. This is most easily shown
by pinging a device via a VLAN tagged interface and it will dump
out the error message and stack trace from netdev_rx_csum_fault.
It has also been seen with standard TCP and UDP packets.
Until this is fully understood, request that the network stack
computes the checksum on packets signalled as having a VLAN tag
applied.
See https://github.com/raspberrypi/linux/issues/2458
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
---
drivers/net/usb/lan78xx.c | 6 +++++-
1 file changed, 5 insertions(+), 1 deletion(-)
diff --git a/drivers/net/usb/lan78xx.c b/drivers/net/usb/lan78xx.c
index 5b46998a6dce..6b61bb21f2ae 100644
--- a/drivers/net/usb/lan78xx.c
+++ b/drivers/net/usb/lan78xx.c
@@ -2920,8 +2920,12 @@ static void lan78xx_rx_csum_offload(struct lan78xx_net *dev,
struct sk_buff *skb,
u32 rx_cmd_a, u32 rx_cmd_b)
{
+ /* Checksum offload appears to be flawed if used with VLANs.
+ * Elect for sw checksum check instead.
+ */
if (!(dev->net->features & NETIF_F_RXCSUM) ||
- unlikely(rx_cmd_a & RX_CMD_A_ICSM_)) {
+ unlikely(rx_cmd_a & RX_CMD_A_ICSM_) ||
+ (rx_cmd_a & RX_CMD_A_FVTG_)) {
skb->ip_summed = CHECKSUM_NONE;
} else {
skb->csum = ntohs((u16)(rx_cmd_b >> RX_CMD_B_CSUM_SHIFT_));
--
2.17.0
From 7528d39c5d01383fadb17a84b9840f9f685d1e0b Mon Sep 17 00:00:00 2001
From: Phil Elwell <phil@raspberrypi.org>
Date: Thu, 19 Apr 2018 17:59:38 +0100
Subject: [PATCH 7/9] lan78xx: Read MAC address from DT if present
There is a standard mechanism for locating and using a MAC address from
the Device Tree. Use this facility in the lan78xx driver to support
applications without programmed EEPROM or OTP. At the same time,
regularise the handling of the different address sources.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
---
drivers/net/usb/lan78xx.c | 42 +++++++++++++++++++--------------------
1 file changed, 20 insertions(+), 22 deletions(-)
diff --git a/drivers/net/usb/lan78xx.c b/drivers/net/usb/lan78xx.c
index 6b61bb21f2ae..6c38a74bb32d 100644
--- a/drivers/net/usb/lan78xx.c
+++ b/drivers/net/usb/lan78xx.c
@@ -37,6 +37,7 @@
#include <linux/irqchip/chained_irq.h>
#include <linux/microchipphy.h>
#include <linux/phy.h>
+#include <linux/of_net.h>
#include "lan78xx.h"
#define DRIVER_AUTHOR "WOOJUNG HUH <woojung.huh@microchip.com>"
@@ -1652,34 +1653,31 @@ static void lan78xx_init_mac_address(struct lan78xx_net *dev)
addr[5] = (addr_hi >> 8) & 0xFF;
if (!is_valid_ether_addr(addr)) {
- /* reading mac address from EEPROM or OTP */
- if ((lan78xx_read_eeprom(dev, EEPROM_MAC_OFFSET, ETH_ALEN,
- addr) == 0) ||
- (lan78xx_read_otp(dev, EEPROM_MAC_OFFSET, ETH_ALEN,
- addr) == 0)) {
- if (is_valid_ether_addr(addr)) {
- /* eeprom values are valid so use them */
- netif_dbg(dev, ifup, dev->net,
- "MAC address read from EEPROM");
- } else {
- /* generate random MAC */
- random_ether_addr(addr);
- netif_dbg(dev, ifup, dev->net,
- "MAC address set to random addr");
- }
-
- addr_lo = addr[0] | (addr[1] << 8) |
- (addr[2] << 16) | (addr[3] << 24);
- addr_hi = addr[4] | (addr[5] << 8);
-
- ret = lan78xx_write_reg(dev, RX_ADDRL, addr_lo);
- ret = lan78xx_write_reg(dev, RX_ADDRH, addr_hi);
+ if (!eth_platform_get_mac_address(&dev->udev->dev, addr)) {
+ /* valid address present in Device Tree */
+ netif_dbg(dev, ifup, dev->net,
+ "MAC address read from Device Tree");
+ } else if (((lan78xx_read_eeprom(dev, EEPROM_MAC_OFFSET,
+ ETH_ALEN, addr) == 0) ||
+ (lan78xx_read_otp(dev, EEPROM_MAC_OFFSET,
+ ETH_ALEN, addr) == 0)) &&
+ is_valid_ether_addr(addr)) {
+ /* eeprom values are valid so use them */
+ netif_dbg(dev, ifup, dev->net,
+ "MAC address read from EEPROM");
} else {
/* generate random MAC */
random_ether_addr(addr);
netif_dbg(dev, ifup, dev->net,
"MAC address set to random addr");
}
+
+ addr_lo = addr[0] | (addr[1] << 8) |
+ (addr[2] << 16) | (addr[3] << 24);
+ addr_hi = addr[4] | (addr[5] << 8);
+
+ ret = lan78xx_write_reg(dev, RX_ADDRL, addr_lo);
+ ret = lan78xx_write_reg(dev, RX_ADDRH, addr_hi);
}
ret = lan78xx_write_reg(dev, MAF_LO(0), addr_lo);
--
2.17.0
From f8f9ad43b37f5db5895619e4304aa9ba286cbbb0 Mon Sep 17 00:00:00 2001
From: Phil Elwell <phil@raspberrypi.org>
Date: Thu, 19 Apr 2018 17:59:40 +0100
Subject: [PATCH 8/9] dt-bindings: Document the DT bindings for lan78xx
The Microchip LAN78XX family of devices are Ethernet controllers with
a USB interface. Despite being discoverable devices it can be useful to
be able to configure them from Device Tree, particularly in low-cost
applications without an EEPROM or programmed OTP.
Document the supported properties in a bindings file.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
---
.../bindings/net/microchip,lan78xx.txt | 54 +++++++++++++++++++
1 file changed, 54 insertions(+)
create mode 100644 Documentation/devicetree/bindings/net/microchip,lan78xx.txt
diff --git a/Documentation/devicetree/bindings/net/microchip,lan78xx.txt b/Documentation/devicetree/bindings/net/microchip,lan78xx.txt
new file mode 100644
index 000000000000..76786a0f6d3d
--- /dev/null
+++ b/Documentation/devicetree/bindings/net/microchip,lan78xx.txt
@@ -0,0 +1,54 @@
+Microchip LAN78xx Gigabit Ethernet controller
+
+The LAN78XX devices are usually configured by programming their OTP or with
+an external EEPROM, but some platforms (e.g. Raspberry Pi 3 B+) have neither.
+The Device Tree properties, if present, override the OTP and EEPROM.
+
+Required properties:
+- compatible: Should be one of "usb424,7800", "usb424,7801" or "usb424,7850".
+
+Optional properties:
+- local-mac-address: see ethernet.txt
+- mac-address: see ethernet.txt
+
+Optional properties of the embedded PHY:
+- microchip,led-modes: a 0..4 element vector, with each element configuring
+ the operating mode of an LED. Omitted LEDs are turned off. Allowed values
+ are defined in "include/dt-bindings/net/microchip-lan78xx.h".
+
+Example:
+
+/* Based on the configuration for a Raspberry Pi 3 B+ */
+&usb {
+ usb-port@1 {
+ compatible = "usb424,2514";
+ reg = <1>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ usb-port@1 {
+ compatible = "usb424,2514";
+ reg = <1>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ ethernet: ethernet@1 {
+ compatible = "usb424,7800";
+ reg = <1>;
+ local-mac-address = [ 00 11 22 33 44 55 ];
+
+ mdio {
+ #address-cells = <0x1>;
+ #size-cells = <0x0>;
+ eth_phy: ethernet-phy@1 {
+ reg = <1>;
+ microchip,led-modes = <
+ LAN78XX_LINK_1000_ACTIVITY
+ LAN78XX_LINK_10_100_ACTIVITY
+ >;
+ };
+ };
+ };
+ };
+ };
+};
--
2.17.0
From be24db04ec2949e9b03763366f100ae40836c61e Mon Sep 17 00:00:00 2001
From: Peter Robinson <pbrobinson@gmail.com>
Date: Mon, 23 Apr 2018 14:31:26 +0100
Subject: [PATCH 9/9] lan78xx: Read LED states from Device Tree
Add support for DT property "microchip,led-modes", a vector of zero
to four cells (u32s) in the range 0-15, each of which sets the mode
for one of the LEDs. Some possible values are:
0=link/activity 1=link1000/activity
2=link100/activity 3=link10/activity
4=link100/1000/activity 5=link10/1000/activity
6=link10/100/activity 14=off 15=on
These values are given symbolic constants in a dt-bindings header.
Also use the presence of the DT property to indicate that the
LEDs should be enabled - necessary in the event that no valid OTP
or EEPROM is available.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
---
MAINTAINERS | 1 +
drivers/net/phy/microchip.c | 25 ++++++++++++++++
drivers/net/usb/lan78xx.c | 32 ++++++++++++++++++++-
include/dt-bindings/net/microchip-lan78xx.h | 21 ++++++++++++++
include/linux/microchipphy.h | 3 ++
5 files changed, 81 insertions(+), 1 deletion(-)
create mode 100644 include/dt-bindings/net/microchip-lan78xx.h
diff --git a/MAINTAINERS b/MAINTAINERS
index 6e950b8b4a41..c7d5f8c60a2c 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -14437,6 +14437,7 @@ M: Microchip Linux Driver Support <UNGLinuxDriver@microchip.com>
L: netdev@vger.kernel.org
S: Maintained
F: drivers/net/usb/lan78xx.*
+F: include/dt-bindings/net/microchip-lan78xx.h
USB MASS STORAGE DRIVER
M: Alan Stern <stern@rowland.harvard.edu>
diff --git a/drivers/net/phy/microchip.c b/drivers/net/phy/microchip.c
index a97ac8c12c4c..2d67937866a3 100644
--- a/drivers/net/phy/microchip.c
+++ b/drivers/net/phy/microchip.c
@@ -21,6 +21,8 @@
#include <linux/phy.h>
#include <linux/microchipphy.h>
#include <linux/delay.h>
+#include <linux/of.h>
+#include <dt-bindings/net/microchip-lan78xx.h>
#define DRIVER_AUTHOR "WOOJUNG HUH <woojung.huh@microchip.com>"
#define DRIVER_DESC "Microchip LAN88XX PHY driver"
@@ -225,6 +227,8 @@ static int lan88xx_probe(struct phy_device *phydev)
{
struct device *dev = &phydev->mdio.dev;
struct lan88xx_priv *priv;
+ u32 led_modes[4];
+ int len;
priv = devm_kzalloc(dev, sizeof(*priv), GFP_KERNEL);
if (!priv)
@@ -232,6 +236,27 @@ static int lan88xx_probe(struct phy_device *phydev)
priv->wolopts = 0;
+ len = of_property_read_variable_u32_array(dev->of_node,
+ "microchip,led-modes",
+ led_modes,
+ 0,
+ ARRAY_SIZE(led_modes));
+ if (len >= 0) {
+ u32 reg = 0;
+ int i;
+
+ for (i = 0; i < len; i++) {
+ if (led_modes[i] > 15)
+ return -EINVAL;
+ reg |= led_modes[i] << (i * 4);
+ }
+ for (; i < ARRAY_SIZE(led_modes); i++)
+ reg |= LAN78XX_FORCE_LED_OFF << (i * 4);
+ (void)phy_write(phydev, LAN78XX_PHY_LED_MODE_SELECT, reg);
+ } else if (len == -EOVERFLOW) {
+ return -EINVAL;
+ }
+
/* these values can be used to identify internal PHY */
priv->chip_id = phy_read_mmd(phydev, 3, LAN88XX_MMD3_CHIP_ID);
priv->chip_rev = phy_read_mmd(phydev, 3, LAN88XX_MMD3_CHIP_REV);
diff --git a/drivers/net/usb/lan78xx.c b/drivers/net/usb/lan78xx.c
index 6c38a74bb32d..01b876daa600 100644
--- a/drivers/net/usb/lan78xx.c
+++ b/drivers/net/usb/lan78xx.c
@@ -37,6 +37,7 @@
#include <linux/irqchip/chained_irq.h>
#include <linux/microchipphy.h>
#include <linux/phy.h>
+#include <linux/of_mdio.h>
#include <linux/of_net.h>
#include "lan78xx.h"
@@ -1760,6 +1761,7 @@ static int lan78xx_mdiobus_write(struct mii_bus *bus, int phy_id, int idx,
static int lan78xx_mdio_init(struct lan78xx_net *dev)
{
+ struct device_node *node;
int ret;
dev->mdiobus = mdiobus_alloc();
@@ -1788,7 +1790,13 @@ static int lan78xx_mdio_init(struct lan78xx_net *dev)
break;
}
- ret = mdiobus_register(dev->mdiobus);
+ node = of_get_child_by_name(dev->udev->dev.of_node, "mdio");
+ if (node) {
+ ret = of_mdiobus_register(dev->mdiobus, node);
+ of_node_put(node);
+ } else {
+ ret = mdiobus_register(dev->mdiobus);
+ }
if (ret) {
netdev_err(dev->net, "can't register MDIO bus\n");
goto exit1;
@@ -2077,6 +2085,28 @@ static int lan78xx_phy_init(struct lan78xx_net *dev)
mii_adv = (u32)mii_advertise_flowctrl(dev->fc_request_control);
phydev->advertising |= mii_adv_to_ethtool_adv_t(mii_adv);
+ if (phydev->mdio.dev.of_node) {
+ u32 reg;
+ int len;
+
+ len = of_property_count_elems_of_size(phydev->mdio.dev.of_node,
+ "microchip,led-modes",
+ sizeof(u32));
+ if (len >= 0) {
+ /* Ensure the appropriate LEDs are enabled */
+ lan78xx_read_reg(dev, HW_CFG, ®);
+ reg &= ~(HW_CFG_LED0_EN_ |
+ HW_CFG_LED1_EN_ |
+ HW_CFG_LED2_EN_ |
+ HW_CFG_LED3_EN_);
+ reg |= (len > 0) * HW_CFG_LED0_EN_ |
+ (len > 1) * HW_CFG_LED1_EN_ |
+ (len > 2) * HW_CFG_LED2_EN_ |
+ (len > 3) * HW_CFG_LED3_EN_;
+ lan78xx_write_reg(dev, HW_CFG, reg);
+ }
+ }
+
genphy_config_aneg(phydev);
dev->fc_autoneg = phydev->autoneg;
diff --git a/include/dt-bindings/net/microchip-lan78xx.h b/include/dt-bindings/net/microchip-lan78xx.h
new file mode 100644
index 000000000000..0742ff075307
--- /dev/null
+++ b/include/dt-bindings/net/microchip-lan78xx.h
@@ -0,0 +1,21 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+#ifndef _DT_BINDINGS_MICROCHIP_LAN78XX_H
+#define _DT_BINDINGS_MICROCHIP_LAN78XX_H
+
+/* LED modes for LAN7800/LAN7850 embedded PHY */
+
+#define LAN78XX_LINK_ACTIVITY 0
+#define LAN78XX_LINK_1000_ACTIVITY 1
+#define LAN78XX_LINK_100_ACTIVITY 2
+#define LAN78XX_LINK_10_ACTIVITY 3
+#define LAN78XX_LINK_100_1000_ACTIVITY 4
+#define LAN78XX_LINK_10_1000_ACTIVITY 5
+#define LAN78XX_LINK_10_100_ACTIVITY 6
+#define LAN78XX_DUPLEX_COLLISION 8
+#define LAN78XX_COLLISION 9
+#define LAN78XX_ACTIVITY 10
+#define LAN78XX_AUTONEG_FAULT 12
+#define LAN78XX_FORCE_LED_OFF 14
+#define LAN78XX_FORCE_LED_ON 15
+
+#endif
diff --git a/include/linux/microchipphy.h b/include/linux/microchipphy.h
index 8f9c90379732..fd1fc8c248ef 100644
--- a/include/linux/microchipphy.h
+++ b/include/linux/microchipphy.h
@@ -78,4 +78,7 @@
#define LAN88XX_EXT_PAGE_TR_LOW_DATA 17
#define LAN88XX_EXT_PAGE_TR_HIGH_DATA 18
+/* Registers specific to the LAN7800/LAN7850 embedded phy */
+#define LAN78XX_PHY_LED_MODE_SELECT (0x1D)
+
#endif /* _MICROCHIPPHY_H */
--
2.17.0